Everything below concerns sublimation. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Last reviewed on 2025-07-30. Where a claim depends on a specific study, the study is described rather than over-claimed.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
A typical cycle begins with freezing, sometimes including an annealing step to control ice crystal size. Freezing conditions influence the pore network that later allows vapor escape. During primary drying, shelf temperature and chamber pressure are set so heat enters the product while its temperature stays below the collapse or eutectic point. Secondary drying then raises the shelf temperature to desorb bound water and lower residual moisture. Cycle design depends on formulation, fill volume, container type, and equipment capability.
Regulatory expectations for lyophilized products focus on consistent manufacture and documented stability. Batches are often monitored for moisture, appearance, potency, and sterility where applicable. Process parameters such as shelf temperature, chamber pressure, and drying time are recorded and controlled within validated ranges. Open questions remain about how best to predict long-term stability from short accelerated studies, especially for complex biologics. Variations in freezing rate and ice crystal size can produce differences that are not always visible but may affect performance.
After drying, a lyophilized product is usually sealed under vacuum or an inert gas to limit moisture uptake. Residual water content is measured because small changes can alter chemical stability and cake appearance. Storage temperature depends on the material; many biological products are kept at 2–8 °C, while some require −20 °C or colder. Exposure to ambient humidity during handling can cause the porous solid to absorb water and collapse. Container closures and stoppers are therefore selected for low moisture transmission and compatibility.
Quality control for lyophilized materials includes visual inspection of the cake, measurement of residual moisture, and tests for reconstitution time. An acceptable cake is typically uniform and may be slightly porous; shrinkage, meltback, or cracks can indicate process deviations. Analytical methods such as Karl Fischer titration, thermogravimetric analysis, and near-infrared spectroscopy quantify water content. Reconstitution time is recorded because a very slow or incomplete dissolution can signal collapse or aggregation. Stability studies compare samples stored under defined temperature and humidity conditions over months or years.
| Property | Value | Notes |
|---|---|---|
| Physical state | Solid, porous cake or powder | Depends on formulation and container |
| Typical storage temperature | 2–25 °C, protected from moisture | Some materials require colder conditions |
| Solubility class | Usually readily soluble after reconstitution | Not an intrinsic chemical property |
| Common analytical method | Karl Fischer titration | Used for residual moisture |
| Common synonyms | Freeze-drying; lyophilisation | Lyophilisation is a spelling variant |
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
After lyophilization, the dried product is often sealed under vacuum or an inert gas to limit moisture and oxygen exposure. Vials, stoppers, and seals must maintain their barrier throughout shelf life. Storage temperature depends on product sensitivity: some cakes tolerate controlled room temperature, while labile biologics require refrigeration. Humidity is a critical variable because dried cakes are hygroscopic and can absorb water when exposed to air. Handling procedures therefore limit open-vial time and use desiccated environments for sampling.
Quality control for lyophilized materials examines appearance, reconstitution time, residual moisture, and mechanical integrity. An acceptable cake is usually uniform and porous, though appearance alone does not prove stability. Karl Fischer titration is a common method for water content, while differential scanning calorimetry can reveal glass transition events. Stability studies track potency, aggregation, and moisture over time under defined temperature and humidity conditions. Specifications are product-specific and may include sterility and endotoxin tests for sterile preparations.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and fixes the structure of the sample. After freezing, primary drying lowers pressure so ice changes directly to vapor without passing through a liquid phase. Secondary drying then removes bound water that remains after ice sublimation. The result is a dry, porous solid that often retains its original shape.
The low pressure used during drying allows water vapor to move from the ice surface to a cold condenser. Energy supplied as heat drives sublimation but must stay below the collapse temperature of the frozen matrix. If the product becomes too warm, the frozen structure may soften or melt, reducing pore formation and slowing drying. Formulations often include bulking agents, stabilizers, or buffers to support a rigid cake. The final moisture content depends on formulation, freezing rate, and the length of secondary drying.
Freeze-drying is distinct from simple evaporation and from spray drying. Evaporation removes water at temperatures above freezing, while spray drying rapidly dries droplets in a heated gas stream. Lyophilization avoids high temperatures, which can be useful for heat-sensitive materials such as proteins, vaccines, and some foods. The porous cake produced by sublimation dissolves or rehydrates more quickly than a dense dried mass. Not all materials tolerate freezing or the pH shifts that can occur as solutes concentrate during ice formation.
Freeze-dried materials are hygroscopic to varying degrees and can take up moisture after drying. Storage therefore often uses sealed glass vials, rubber stoppers, and crimp seals to limit contact with ambient humidity. A desiccant may be included for moisture-sensitive products, although it is not universal. Controlled room temperature is sufficient for many lyophilizates, while others require refrigeration or freezing. Moisture ingress remains a primary cause of cake collapse, chemical degradation, and loss of reconstitution performance.
Quality assessment of a lyophilized product includes cake appearance, residual moisture, reconstitution time, and container closure integrity. A uniform, porous cake suggests that freezing and drying stayed within the formulation's design space. Cracks, shrinkage, meltback, or a glassy film can indicate thermal abuse or a formulation problem. Analysts also test for subvisible particles and sterility when the product requires those specifications. Visual inspection alone cannot confirm biological activity or chemical stability, so it is combined with analytical methods.
==== Inverted burial ==== For humans, maintaining an upside-down position, with the head vertically below the feet, is highly uncomfortable for any extended period of time, and consequently burial in that attitude (as opposed to attitudes of rest or watchfulness, as above) is highly unusual and generally symbolic. Occasionally suicides and assassins were buried upside down, as a post-mortem punishment and (as with burial at cross-roads) to inhibit the activities of the resulting undead. In Gulliver's Travels, the Lilliputians buried their dead upside down:
== Introduction == Unlike epithelial cells – which are stationary and characterized by an apico-basal polarity with binding by a basal lamina, tight junctions, gap junctions, adherent junctions and expression of cell-cell adhesion markers such as E-cadherin, mesenchymal cells do not make mature cell-cell contacts, can invade through the extracellular matrix, and express markers such as vimentin, fibronectin, N-cadherin, Twist, and Snail. MET plays also a critical role in metabolic switching and epigenetic modifications. In general, epithelium-associated genes are upregulated and mesenchyme-associated genes are downregulated in the process of MET.
=== Election misinformation === Ayyadurai has continued to spread misinformation since about the 2020 presidential election. At Mike Lindell's Cyber Symposium in August 2021, he claimed there were "serious issues" in the election process involving voting machines able to "multiply a vote by a factor" and that states were illegally not "saving ballot images". In fact, not all states are legally required to store ballot images. In August 2021, he was hired by the Arizona Senate—as part of the controversial 2021 Maricopa County presidential ballot audit—to "review signatures on the envelopes of 1.9 million early ballots sent to [Maricopa] county". In late September, he remotely attended the Arizona state senate presentation of the review's findings where he questioned the validity of some signatures on mail ballot envelopes, and criticized and gave a presentation filled with misrepresentations about the county's signature verification process.
== Species == At times in the past, taxonomists included many species in the genus Gadus (from Ancient Greek: γάδος, romanized: gádos). Most of these are now either classified in other genera or have been recognized as forms of one of three species. All these species have several common names, most of them ending with the word "cod" (see naming), whereas other species, closely related, have other common names (such as pollock and haddock). However, many other unrelated species also have common names ending in "cod". Usage often varies across localities and over time.
A third‑generation Kamiokande detector, Hyper‑Kamiokande, is currently under construction and it will be about 5.2 times more massive than Super-Kamiokande (approximately 8 times larger in fiducial volume), designed to start data taking in 2028. It will achieve sensitivities 3–5 times better than Super-Kamiokande after 10 years of data taking. Other important experiments that will have competitive sensitivities in proton decay searches are JUNO in China (which started data taking in January 2026) and DUNE in the US (designed to start data taking in 2031). These three ambitious projects were originally proposed and funded primarily for neutrino‑oscillation studies, but they will nevertheless be able to probe proton decay with high sensitivity, as summarized in the following table.
Sources: en.wikipedia.org
=== Vascular endothelial growth factor === Vascular endothelial growth factor (VEGF) is widely recognized for its role in angiogenesis and vascular homeostasis. However, beyond its classical extracellular signaling functions, VEGF also exerts intracellular, or intracrine, effects, particularly in cardiac tissues. Intracrine VEGF plays a significant role in cardiac development, angiogenesis, and the adaptive response to ischemic injury.
Sheikh Hazza bin Zayed bin Sultan Al Nahyan (Arabic: هزاع بن زايد بن سلطان آل نهيان; born 2 June 1965) is the younger brother of the President of the United Arab Emirates Sheikh Mohamed bin Zayed Al Nahyan, Ruler's Representative of Al Ain Region of the Emirate of Abu Dhabi, former National Security Advisor of the UAE and Deputy Chairman of Abu Dhabi Executive Council.
This led in 1976 to the development and introduction of Progestasert, a progesterone-containing product and the first progestogen-containing IUD. Unfortunately, the product had various problems that limited its use. These included a short duration of efficacy of only one year, a high cost, a relatively high 2.9% failure rate, a lack of protection against ectopic pregnancy, and difficult and sometimes painful insertions that could necessitate use of a local anesthetic or analgesic. As a result of these issues, Progestasert never became widely used, and was discontinued in 2001. It was used mostly in the United States and France while it was marketed.
Among measures it introduces is a licensing scheme for land where grouse shooting takes place, and regulations for traps. 22 March – A report prepared by Stirling University calls for artificial 3G football pitches to be banned in Scotland because they contain potentially cancer causing chemicals. Jasmin Paris from Midlothian becomes the first woman to complete the Barkley Marathons in the US state of Tennessee, doing so with one minute 39 seconds to spare of the 60-hour cut off. 27 March – Following a three-week hearing at Edinburgh Sheriff Court, former private school teacher John Brownlee, who worked at the Edinburgh Academy between 1967 and 1987, is found to have physically abused bos in his charge. He will not face trial though as he was earlier deemed to be medically unfit to do so. A group calling itself INC Ransom threatens to publish data stolen from NHS Dumfries and Galloway. VisitScotland announces that its 25 information centres will close over the next two years. 28 March – The Assisted Dying for Terminally Ill Adults (Scotland) Bill, a bill to legalise assisted dying in Scotland and drafted by Liberal Democrat MSP Liam McArthur, is introduced into the Scottish Parliament.
Sources: en.wikipedia.org
Freezing only converts liquid to solid. Lyophilization adds vacuum and controlled warming so frozen solvent sublimes, leaving a dry porous solid. The two steps are related but not interchangeable.
Reduced pressure keeps the solvent below its triple point, allowing ice to become vapor without melting. Vacuum also helps remove water vapor from the product chamber. The exact pressure is chosen with the formulation and equipment.
Residual moisture is water that remains in the dried solid after secondary drying. It is often measured by Karl Fischer titration, near-infrared spectroscopy, or thermogravimetry. Acceptable levels depend on the material and its stability profile.
Most are held in sealed containers at controlled temperatures, often 2–8 °C, while some require frozen storage. Protection from moisture and light helps preserve the dry matrix. Exact conditions are set by the manufacturer or study protocol.