Secondary drying is one of those subjects where the details matter more than the headlines. This page pulls together the background, the mechanisms, and the practical points readers ask about most.
Last reviewed on 2025-09-02. Where a claim depends on a specific study, the study is described rather than over-claimed.
Stability of a lyophilized product depends on its glass transition temperature, the temperature at which the amorphous cake transitions from a glassy to a rubbery state. Storage below this temperature minimizes molecular mobility and slows chemical degradation. If the storage temperature exceeds the glass transition temperature, the cake may collapse, shrink, or become sticky. Accelerated stability studies at elevated temperatures and humidity help predict shelf life, but they do not always reflect real-time behavior. Residual moisture content also plays a critical role in long-term stability.
Reconstitution involves adding a suitable diluent, often sterile water or a buffer, to the dried cake. Gentle swirling or inversion helps dissolve the material without creating excessive foam. The time required for complete dissolution can range from seconds to several minutes and depends on the cake structure and the diluent. Improper reconstitution, such as vigorous shaking or using the wrong diluent, can cause protein aggregation or loss of activity. After reconstitution, the product may have a limited shelf life and should be used according to its labeling.
Lyophilized products are typically hygroscopic and require protection from moisture during storage. Manufacturers seal them in glass vials, often under vacuum or an inert gas such as nitrogen. The container closure system, including the stopper and crimp seal, must prevent water vapor ingress. Storage temperature varies from controlled room temperature to refrigerated or frozen conditions, depending on the formulation. Humidity-controlled environments are essential because even brief exposure to ambient air can degrade the product.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
| Property | Value | Notes |
|---|---|---|
| Appearance | White to off-white porous cake | Color depends on formulation. |
| Typical storage temperature | 2–8 °C | Refrigerated for many biologics. |
| Residual moisture | <1% to 3% | Low moisture improves stability. |
| Container | Sealed glass vial | Often with rubber stopper and aluminum crimp. |
| Reconstitution time | Seconds to minutes | Varies with cake density and diluent. |
Quality control for freeze-dried lots combines visual inspection with instrumental tests. Cake appearance, color, and shrinkage are recorded against a reference, while residual moisture is measured by Karl Fischer titration or loss on drying. Thermal analysis can reveal phase transitions and crystallization events, and X-ray diffraction distinguishes amorphous from crystalline solids. Microbiological tests and container closure integrity checks are also routine for sterile products. Analytical methods must be validated for the matrix, because excipients and low moisture can affect accuracy. Open questions include how best to predict long-term stability from short-term data.
Lyophilized solids are often hygroscopic, so handling occurs in controlled low-humidity areas or glove boxes when the material is exposed. Vials remain sealed with elastomeric stoppers and aluminum crimps until use, because airborne moisture can raise residual water and shorten shelf life. The porous cake is fragile and may crack, shrink, or powder during transport. Personnel typically avoid repeated warming and cooling of sealed units, which can draw moisture through closures. These practices aim to preserve the low water content achieved during drying.
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
Quality control for lyophilized materials includes visual inspection, residual moisture measurement, and reconstitution testing. Cake appearance can reveal process problems such as collapse, shrinkage, or meltback, although appearance alone does not prove potency. Residual moisture is commonly measured by Karl Fischer titration or by loss on drying. Reconstitution time is checked because a slow or incomplete dissolve can indicate a change in pore structure. Stability studies track these attributes over time under defined temperature and humidity conditions.
Analytical methods for lyophilized solids must account for the low moisture content and the fragile cake. Karl Fischer titration is widely used for water content, while near-infrared spectroscopy can measure moisture non-destructively in sealed containers. X-ray diffraction and modulated differential scanning calorimetry help identify crystalline or amorphous phases. Residual solvent analysis may be needed if organic solvents were used during formulation. The combination of these methods supports batch release and long-term stability assessment.
Lyophilized products are typically stored as sealed solids in vials or syringes. Moisture ingress is a major concern because many dried cakes are hygroscopic and can lose stability when exposed to humid air. Storage temperature depends on the formulation; some products are kept refrigerated, while others are stable at room temperature. Container closure integrity and headspace moisture are often monitored. Light protection may also be required for some photosensitive materials.
Secondary drying removes bound water that remains after ice sublimation. Shelf temperature is raised gradually while pressure remains low, reducing water content to a target range. Over-drying can cause brittleness or electrostatic issues, while under-drying affects stability. The endpoint is often judged by pressure rise tests, temperature measurements, or water content analysis. Scale-up depends on matching heat and mass transfer across equipment sizes. Small changes in shelf temperature or pressure can alter cycle length substantially.
Lyophilization, or freeze-drying, removes water from a material by freezing it and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intervening liquid state. It is used for heat-sensitive materials that would degrade in conventional drying. The three stages are freezing, primary drying, and secondary drying, each with distinct temperature and pressure requirements. In practice, cycle design balances these variables.
Catalase is a common enzyme found in nearly all living organisms exposed to oxygen (such as bacteria, plants, and animals) which catalyzes the decomposition of hydrogen peroxide to water and oxygen. It is a very important enzyme in protecting the cell from oxidative damage by reactive oxygen species (ROS). Catalase has one of the highest turnover numbers of all enzymes; one catalase molecule can convert millions of hydrogen peroxide molecules to water and oxygen each second. Catalase is a tetramer of four polypeptide chains, each over 500 amino acids long. It contains four iron-containing heme groups that allow the enzyme to react with hydrogen peroxide. The optimum pH for human catalase is approximately 7, and has a fairly broad maximum: the rate of reaction does not change appreciably between pH 6.8 and 7.5. The pH optimum for other catalases varies between 4 and 11 depending on the species. The optimum temperature also varies by species.
Botany, also called plant science, is the branch of natural science and biology that studies the growth, reproduction and evolution of plants over the last 3.5 billion years of life on earth. As with all areas of biology and medicine, plants can be studied at range of levels from their biochemistry, molecular biology, cell biology and genetics to their ecology, pathology, anatomy, morphology and taxonomy. A botanist or plant scientist is a scientist who specialises in this field. Plants can be defined in multiple ways including approximately 410,000 species of land plants, and some 391,000 species of vascular plants, of which approximately 369,000 are flowering plants and approximately 20,000 bryophytes. Botany originated from prehistoric herbalism to identify and cultivate plants that were edible, poisonous, and medicinal, making it one of the first endeavours of human investigation. Medieval physic gardens, often attached to monasteries, contained plants that possibly had medicinal benefits. They were forerunners of the first botanical gardens attached to universities, founded from the 1540s onwards. One of the earliest was the Padua botanical garden. These gardens facilitated the academic study of plants. Efforts to catalogue and describe their collections were the beginnings of plant taxonomy and led in 1753 to the binomial system of nomenclature of Carl Linnaeus that remains in use to this day for the naming of all biological species.
Hird's lawyer, Steven Amendola, asserted that the AFL withdrew all charges against Hird under the deeds of settlement that he and the club signed with the AFL. At the time of the media report, Hird was considering legal action against both the AFL and Demetriou. Essendon chairman Paul Little said that Hird would be wanted as the senior coach once his suspension was served and that he had been offered a two-year extension from 2015, which would have seen him coaching until the end of the 2016 season. However, Hird resigned after round 20 in August 2015, near the end of the season, with the team near the bottom of the ladder.
== Further reading == Müller, Rainer H.; Mäder, Karsten; Gohla, Sven (3 July 2000). "Solid lipid nanoparticles (SLN) for controlled drug delivery – a review of the state of the art". European Journal of Pharmaceutics and Biopharmaceutics. 50 (1): 161–177. doi:10.1016/S0939-6411(00)00087-4. PMID 10840199. Shah, Mansi K.; Madan, Parshotam; Lin, Senshang (June 2014). "Preparation, in vitro evaluation and statistical optimization of carvedilol-loaded solid lipid nanoparticles for lymphatic absorption via oral administration". Pharmaceutical Development and Technology. 19 (4): 475–485. doi:10.3109/10837450.2013.795169. PMID 23697916. S2CID 42174732. Shah, Mansi K.; Madan, Parshotam; Lin, Senshang (3 October 2015). "Elucidation of intestinal absorption mechanism of carvedilol-loaded solid lipid nanoparticles using Caco-2 cell line as an in-vitro model". Pharmaceutical Development and Technology. 20 (7): 877–885. doi:10.3109/10837450.2014.938857. PMID 25069593. S2CID 40506806.
The argument for keeping the term "atomic weight" was primarily that it was a well understood term to those in the field, that the term "atomic mass" was already in use (as it is currently defined) and that the term "relative atomic mass" might be easily confused with relative isotopic mass (the mass of a single atom of a given nuclide, expressed dimensionlessly relative to 1/12 of the mass of carbon-12; see section above). In 1979, as a compromise, the term "relative atomic mass" was introduced as a secondary synonym for atomic weight. Twenty years later the primacy of these synonyms was reversed, and the term "relative atomic mass" is now the preferred term. However, the term "standard atomic weights" (referring to the standardized expectation atomic weights of differing samples) has not been changed, because simple replacement of "atomic weight" with "relative atomic mass" would have resulted in the term "standard relative atomic mass".
Sources: en.wikipedia.org
sustaining high routine Full Immunized Child (FIC) coverage of at least 90% in all provinces and cities; sustaining the polio-free country for global certification; eliminating measles by 2008; and eliminating neonatal tetanus by 2008.
=== Mechanical properties === Crystalline cellulose has a stiffness about 140–220 GPa, comparable with that of Kevlar and better than that of glass fiber, both of which are used commercially to reinforce plastics. Films made from nanocellulose have high strength (over 200 MPa), high stiffness (around 20 GPa) but lack of high strain (12%). Its strength/weight ratio is 8 times that of stainless steel. Fibers made from nanocellulose have high strength (up to 1.57 GPa) and stiffness (up to 86 GPa).
=== Other components === Autonomy and freedom are often-discussed factors of well-being. They concern the possibility to choose, the ability to make informed decisions without coercion, and the capacity to act without being constrained by external forces. Individuals with a high level of autonomy and freedom tend to be more satisfied by having control over their lives. This enables them to decide between important options and choose a life that reflects their desires, preferences, and values. However, these conditions may not automatically lead to well-being and can sometimes have negative consequences. For example, a person lacking mental maturity and wisdom may freely engage in short-sighted pleasures with instant gratification while ignoring negative long-term consequences. Eudaimonic conceptions of well-being stress the importance of character traits and virtues. Character traits are stable and consistent aspects of personality that influence how people think, feel, and act. Traits associated with well-being include wisdom, courage, kindness, justice, temperance, and gratitude. Virtues are character traits that promote ethical excellence, such as dispositions to act morally and follow ethical principles. Virtue-based theories of well-being argue that virtue can be its own reward, for example, because living a morally upright life can be a fulfilling experience. However, virtue and well-being may also conflict in some cases, for instance, when altruistic service to a greater good requires personal sacrifice.
== AFL career == Lovett-Murray was initially rookie listed by Collingwood, playing for the Williamstown Seagulls in the Victorian Football League. After switching to the Bendigo Bombers, he was rookie listed by Essendon in the 2003 Rookie Draft. Lovett-Murray was promoted to the senior list early in the 2004 season and played 20 games. He spent the 2005 season on the rookie list again, he was promoted again that season and stayed on the senior list since then. In 2006, Lovett-Murray copped a three-game suspension from the AFL Tribunal for intentionally striking Fremantle midfielder Matthew Carr in the Bombers' round fourteen loss to the Dockers at Subiaco Oval. This was one of many lowlights for the club, which finished 15th at the end of the season with just three wins and one draw from 22 matches played. Lovett-Murray, along with 33 other Essendon players, was found guilty of using a banned performance-enhancing substance, thymosin beta-4, as part of Essendon's sports supplements program during the 2012 season. He and his team-mates were initially found not guilty in March 2015 by the AFL Anti-Doping Tribunal, but a guilty verdict was returned in January 2016 after an appeal by the World Anti-Doping Agency. He was suspended for two years which, with backdating, ended in December 2016; as a result, he served approximately fifteen months of his suspension and missed the entire 2016 season, when he had intended to play and coach for Rumbalara Football Club.
== Uses == Niosomes are used as biodegradable and non-immunogenic drug delivery compounds, as they have a low toxicity risk in biological systems. They can also be used to entrap hydrophilic pharmaceuticals within aqueous compartments or lipophilic drugs into vesicular bilayer membranes. Niosomes shield drug molecules from the biological environment, which can be utilized to improve the therapeutic performance of various drug molecules. Additionally, they can be used in a sustained drug delivery system to more directly affect target cells and delay clearance from circulation. Niosomes are used in a variety of applications, including gene delivery, drug targeting, antineoplastic treatment, delivery of peptide drugs, carriers for hemoglobin, transdermal drug delivery systems, and cosmetics. They are also being studied for their potential use as a treatment for different forms of leishmaniasis In one 2022 in vitro study, tamoxifen-loaded niosomes exhibited pH-dependent release and induced apoptosis and cell-cycle arrest in two breast cancer cell lines .
Sources: en.wikipedia.org
The football team began at The University of Arizona in 1899 under the nickname "Varsity" (a name kept until the 1914 season when the team was deemed the "Wildcats"). The football team was notably successful in the 1990s, under head coach Dick Tomey; his "Desert Swarm" defense was characterized by tough, hard-nosed tactics. In 1993, the team had its first 10-win season and beat the University of Miami Hurricanes in the Fiesta Bowl by a score of 29–0. It was the bowl game's only shutout in its then 23-year history. In 1998, the team posted a school-record 12–1 season and made the Holiday Bowl in which it defeated the Nebraska Cornhuskers. Arizona ended the season ranked 4th nationally in the coaches and API poll. The 1998 Holiday Bowl was televised on ESPN and set the now-surpassed record of being the most-watched bowl game in the network's history. From November 2003 until October 2011, the program was led by Mike Stoops, brother of Bob Stoops, the head football coach at the University of Oklahoma (the 2000 BCS national champions); Stoops was fired on October 10, 2011. Former Michigan and West Virginia head coach Rich Rodriguez was hired on November 21, 2011, to lead the Wildcats. The announcement was made by UA athletic director Greg Byrne via Twitter. In his first season, Rodriguez took the Wildcats to the 2012 New Mexico Bowl, where they defeated the University of Nevada Wolf Pack. In his third season, the Wildcats won the Pac-12 South and played in the 2014 Fiesta Bowl.
== History == World Refrigeration Day was the idea of refrigeration consultant Stephen Gill, former president of the Institute of Refrigeration in the UK. In October 2018, ASHRAE (The American Society of Heating, Refrigerating and Air-Conditioning Engineers) pledged support for World Refrigeration Day. In January 2019, ASHRAE awarded Gill its John F James International Award in Atlanta. In February 2019, the United Nations Environment Programme pledged support at the UNEP national ozone officers meeting in Paris. The inaugural World Refrigeration Day was held on 26 June 2019.
India is a parliamentary republic with a multi-party system. There are six recognised national parties in the country, including the Indian National Congress (generally, "the Congress") and the Bharatiya Janata Party (BJP); there are over 50 regional parties. The Congress is considered the ideological centre in Indian political culture; the BJP is right-wing to far-right.
In March 2020, the Roche Diagnostics division reached a significant milestone with the FDA-approval of its high-volume Sars-CoV-2 diagnostic test, capable of analysing 1,400-8,800 samples within 24h on the proprietary Cobas 6800/8800 molecular testing system. In September, the business acquired Ireland-based Inflazome, for €380 million, gaining control of its NLRP3 inflammasome inhibitors. In March 2021, Roche announced it would acquire GenMark Diagnostics for $1.8 billion. Under the terms of agreement, Genmark diagnostics will become a subsidiary and the principal operations will continue to remain in Carlsbad, California. In September, the company announced it would acquire German biotech group, TIB Molbiol, enhancing its molecular diagnostics operations. In September 2022, Roche acquired Good Therapeutics at a cost of $250M for its PD1-regulated IL-2 receptor agonist program. In July 2023, Roche partnered with Alnylam Pharmaceuticals in a deal worth $2.8 billion for the development of a hypertension drug. In December 2023, Roche acquired Carmot Therapeutics, an anti-obesity drug developer, for $2.7 billion. In October 2023, Monte Rosa Therapeutics and Roche signed a strategic cooperation and licensing agreement for the discovery and development of molecular adhesive degradators (MGD) to combat cancer and neurological diseases. The partnership includes Monte Rosa's QuEENT discovery engine and Roche Holding expertise.
Dimethylformamide, DMF is an organic compound with the chemical formula HCON(CH3)2. Its structure is HC(=O)−N(−CH3)2. Commonly abbreviated as DMF (although this initialism is sometimes used for dimethylfuran, or dimethyl fumarate), this colourless liquid is miscible with water and the majority of organic liquids. DMF is a common solvent for chemical reactions. Dimethylformamide is odorless, but technical-grade or degraded samples often have a fishy smell due to impurity of dimethylamine. Dimethylamine degradation impurities can be removed by sparging samples with an inert gas such as argon or by sonicating the samples under reduced pressure. As its name indicates, it is structurally related to formamide, having two methyl groups in the place of the two hydrogens. DMF is a polar (hydrophilic) aprotic solvent with a high boiling point. It facilitates reactions that follow polar mechanisms, such as SN2 reactions.
Sources: en.wikipedia.org
Lyophilized products should be stored in airtight containers, protected from moisture and light, at the temperature specified by the manufacturer. Many require refrigeration at 2–8 °C, while some need frozen storage. Always check the product label for specific conditions.
Moisture can cause the porous cake to collapse, increase molecular mobility, and accelerate chemical degradation. It may also promote microbial growth if the product lacks preservatives. Proper sealing and handling are essential to maintain stability.
Some formulations contain labile biological molecules that degrade even in the dry state at higher temperatures. Others have a low glass transition temperature, meaning the cake can soften or collapse at room temperature. Cold storage reduces molecular motion and slows degradation.
Primary drying removes ice by sublimation under vacuum. Secondary drying removes water that is bound to the material, often by warming the product after most ice has left. Both stages occur below temperatures that would cause unwanted melting.